Jandy Fusion Soft Salt System O-Ring Kit | R0502500

The factory-genuine Jandy R0502500 O-Ring Kit is an indispensable service package for Zodiac Nature2 Fusion Soft salt chlorinators, delivering a full set of replacement seals for every critical internal connection. This kit contains eight premium rubber o-rings specifically sized to fit collars, unions, shafts, and drain plugs throughout the system. Each o-ring is engineered to seal out leaks and sustain reliable operation even under intense...

Jandy Fusion Soft Salt System Small Collar with O-Ring | R0502400

The factory-original Jandy R0502400 Small Collar with O-Ring is a purpose-designed replacement component for Zodiac Nature2 Fusion Soft Salt Systems, crafted to form a snug, watertight connection inside your chlorination unit. This part plays a vital role in preserving proper system pressure and uninterrupted water circulation, protecting against performance degradation caused by drips or insecure fittings. Built from resilient, pool-rated materials, it holds up against...

Jandy Gasket Header Kit for Hi-E2 Pool Heaters - R0304300

The Jandy Gasket Header Kit R0304300 is a factory-original sealing package engineered specifically for Jandy Hi-E2 pool and spa heaters, with a focus on models 220 and 350. This comprehensive kit supplies every gasket and sealing component necessary to create a leak-proof junction between the header and surrounding parts. Made from robust, pool-grade materials, these gaskets are designed to hold up against the heat, pressure,...

Jandy Header Gasket Assembly 18-Pack for Laars & Lite2 Heaters - R0050800

The Jandy Header Gasket Assembly R0050800 is a complete factory-original gasket package designed to reseal the header components of Jandy Lite2 and Laars pool and spa heaters. This OEM set contains 18 precisely engineered gaskets that target every critical sealing point within the header assembly where leaks commonly develop. Swapping out these gaskets restores proper internal pressure, stops water loss, and bolsters overall heater performance....

Jandy Heater 2 PSI Air Pressure Switch R0013200 by Swimables | SW-44-132

The Swimables SW-44-132 Air Pressure Switch is an essential safety device engineered for Jandy and Zodiac pool and spa heaters, calibrated to operate at 2 PSI. Its primary function is to verify adequate water flow through the heater before and during operation. When water pressure falls below the designated threshold, the switch triggers a shutdown to protect the heat exchanger from overheating and potential damage....

Jandy High Limit Switch 135F & 150F for Laars and Lite2 Heaters - R0023200

The Jandy High Limit Switch Set R0023200 is a factory-original dual-safety thermal protection package for numerous Jandy and Laars pool and spa heaters. This kit contains two precision-calibrated switches—one rated at 135°F and the other at 150°F—that provide layered shutdown protection when temperatures rise beyond their designated limits. Together, these components guard against thermal damage while keeping the system operating within safe parameters. Built for...

Jandy High Limit Switch Harness | LXi & LRZE Pool Heater | R0457400

The Jandy High Limit Switch Harness R0457400 is an authentic OEM wiring assembly designed for Jandy LXi and LRZE pool and spa heaters. This harness forms the electrical bridge between the high limit switches and the main control board, carrying the critical safety signals that trigger an automatic shutdown when water temperature exceeds safe operating limits. Without a functioning harness, the heater's overheat protection cannot...

Jandy High Limit Switch Set 130F & 150F | LXi Pool Heater | R0457200

The Jandy High Limit Switch Set R0457200 is a genuine OEM dual-switch safety kit designed to protect Jandy LXi pool and spa heaters from dangerous overheating conditions. Containing two independent high limit switches, this set triggers an automatic system shutdown whenever water temperature climbs beyond preset safe boundaries. The dual-switch configuration provides built-in redundancy, so even if one switch malfunctions, the second unit continues to...

Jandy Hot Surface Ignitor | LXi Pool Heater Replacement | R0457500

The Jandy Hot Surface Ignitor R0457500 is a genuine OEM silicon carbide glow bar engineered for Jandy LXi Low NOx pool and spa heaters. When the thermostat signals a demand for heat, this ignitor rapidly reaches the extreme temperatures needed to ignite gas safely and consistently. Beyond its ignition role, it doubles as a flame sensor, continuously verifying that a flame is present throughout the...

Jandy Igniter Kit for JXi Pool Heaters | OEM Replacement | R0457502

The Jandy Igniter Kit R0457502 is a factory-original replacement package designed to deliver fast, dependable ignition in JXI pool and spa heaters. Manufactured to Jandy's OEM specifications, this igniter produces rapid heat-up times so your heater starts without hesitation, even after extended periods of inactivity. Its robust construction is built to endure the intense thermal demands of repeated ignition cycles in outdoor environments. As a...

Jandy Ignition Control Module | JXi & LXi Pool Heater Replacement | R0456900

The Jandy Ignition Control R0456900 is a factory-original hot surface ignition module engineered for Jandy JXi and LXi Low NOx gas pool and spa heaters. This module orchestrates the electronic signals that initiate gas ignition, serving as the brain behind every heating cycle's safe and timely startup. With accurate ignition timing built into its circuitry, your heater fires reliably with minimal delay, keeping downtime to...

Jandy Impeller Kit for SWF125 0.75HP & SHPF 5HP Pumps | R0807207

The Jandy R0807207 is a factory-genuine impeller kit built to serve both the Jandy SWF125 0.75HP and SHPF 5.0HP pump platforms. This package contains a closed-face impeller, attachment screw, and backplate O-ring, delivering every component necessary to restore full hydraulic function. The closed-face impeller architecture handles elevated pressure demands with ease, making it well suited for both residential and commercial pool applications. With all required...

Jandy Infinite WaterColors LED Pool Light | 40W 14V 100' Cord | IWCP50W100

Jandy Interface Bezel & Display Cover | LXi Pool Heater | R0458400

The Jandy Interface and Bezel Display Cover R0458400 is a genuine OEM protective housing engineered specifically for Jandy LXi pool and spa heaters. This assembly combines the display interface frame with a precision-molded bezel that shields the control panel from rain, dust, direct sunlight, and other outdoor hazards. By keeping moisture and debris away from the electronic display, it preserves screen clarity, button responsiveness, and...

Jandy IQPUMP01 Pool Pump Automation Controller System

Jandy Iron Bypass Assembly Kit for Lite, Lite2 & ESC Heaters - R0054900

The Jandy Iron Bypass Assembly Kit R0054900 is a factory-original component designed to optimize water flow management in Jandy Lite, Lite2, and ESC series pool and spa heaters. This assembly is instrumental in balancing the relationship between water circulation and heat output, enabling the system to achieve accurate and efficient temperature control without placing excessive strain on the heater. Fabricated from resilient materials capable of...

Jandy JHP & PHP Pump Diffuser O-Ring 0.75HP-2.5HP | R0558701

The genuine Jandy Diffuser O-Ring R0558701 is a factory-original replacement component precision-engineered for Jandy JHP and PHP series pool and spa pumps. This carefully molded O-ring establishes a vital watertight barrier between the pump diffuser and housing, maintaining correct pressure levels and guarding against leaks that could diminish pump output or harm internal parts. Engineered to fit pump models spanning 0.75 HP to 2.5 HP,...

Jandy JS Series Sand Filter Replacement Lid | R0487300

Protect the top of your Jandy JS Series Sand Filter with the genuine Jandy Lid R0487300, a factory-original closure designed to maintain airtight pressure within the filter tank. This OEM lid forms a positive seal that keeps system pressure where it belongs, supporting maximum sand bed contact and efficient particulate removal. Molded from robust, pool-grade material that resists degradation from chlorine, bromine, and sun exposure,...

Jandy JS-100SM Filter 30 Inch Hub with Laterals | R0488000

Upgrade the internal distribution system of your Jandy JS100-SM sand filter with the genuine Jandy R0488000 Hub Assembly featuring 30" Laterals. This factory-engineered assembly sits at the base of the filter tank and spreads return water uniformly across the entire sand bed, maximizing the media's ability to trap suspended particles and deliver visibly clearer pool water. Constructed from corrosion-proof materials rated for constant submersion in...

Jandy JXi 400 Gas Orifice Conversion Kit R0591608 | Natural Gas to Propane

The Jandy Gas Orifice Kit R0591608 is a genuine OEM propane conversion package created for JXi 400 pool and spa heaters, enabling a secure changeover from natural gas to propane fuel. This kit contains all precision-sized orifices and associated fittings needed to bring your heater into full compliance with propane operating parameters after the transition. Whether motivated by changes in fuel availability, personal energy preferences,...