Polaris Large Wheel Replacement for Vac-Sweep 180 & 280 Pool Cleaners – C6

Give your Polaris pool cleaner the traction and stability it needs with the genuine Polaris Large Wheel C6. Built as a direct replacement for Polaris 180 and 280 cleaners, this 6.5-inch diameter wheel serves as a primary drive component, guiding the cleaner across the pool floor and up walls with reliable, consistent motion. Manufactured from tough, wear-resistant materials, it delivers the structural strength required for...

Polaris Lock Washers for Vac-Sweep 180 & 280 Pool Cleaners – C45 | 5 Pack

Keep every fastener on your Polaris pool cleaner locked tight with the genuine Polaris Lock Washers C45. Sold in a convenient five-pack, these factory-original washers are designed for Polaris Vac-Sweep 180 and 280 cleaners, where they secure the screws within the swing axle assembly and prevent them from vibrating loose during operation. Manufactured from tough, corrosion-resistant materials, they play a small but vital role in...

Polaris MaxTrax Black Tire C11 | Pool Cleaner Replacement

Restore peak traction and dependable pool navigation with the genuine Polaris MaxTrax Tire C11. This black rubber replacement tire is purpose-built for Polaris pressure-side cleaners, fitting models 180, 280, 360, 380, TR36P, TR35P, F4TR, and F4000D. Its advanced tread pattern grips slippery pool walls and floors with confidence, enabling your cleaner to traverse every inch of your pool without scratching or marring any surface. Crafted...

Polaris Maxx & Atlas Cleaner Factory Tune Up Kit R0997900

Revitalize your suction-side pool cleaner with the genuine Polaris R0997900 Factory Tune-Up Kit, a comprehensive maintenance package specifically assembled for Polaris Maxx and Atlas models. Packed with critical wear-item replacements, this kit addresses common performance degradation by renewing the components most susceptible to everyday use. Rather than investing in a full cleaner replacement, this tune-up restores strong suction, smooth navigation, and thorough debris pickup. Designed...

Polaris Orifice Tip With Guard for Pool Cleaners - B25

Genuine Polaris B25 Orifice Tip with Guard is an essential replacement component for Polaris pool cleaners spanning models 180, 280, 360, 380, TR35P, P39, and 3900 Sport. This part focuses pressurized water into a concentrated jet that blasts debris out of corners, off steps, and from other hard-to-reach zones throughout your pool. A built-in protective guard shields the orifice tip from impact damage and abrasion,...

Polaris PB4-60 Booster Pump for Pressure Side Pool Cleaners | 3/4 HP

The genuine Polaris PB4-60 Booster Pump delivers 3/4 HP of dedicated power to supercharge the cleaning ability of Polaris pressure-side pool cleaners. Wired for 115 or 230 volts and consuming 12.8 or 6.4 amps accordingly, this pump produces reliable, unwavering water pressure that drives comprehensive debris removal from every corner of your pool. Engineered for rugged longevity and whisper-quiet operation, the PB4-60 supports hassle-free pool...

Polaris PB4-60 Old Style Booster Pump Impeller Replacement | P15

The OEM Polaris P15 Impeller is an essential rotating component engineered specifically for PB4-60 booster pumps, responsible for directing water flow and sustaining reliable pressure output. Manufactured from premium, wear-resistant materials, this impeller thrives under the constant demands of pool pump operation. Periodic inspection and replacement of this part is critical to keeping your pump performing efficiently and your pool cleaner working at its best....

Polaris PB4SQ Booster Pump Body Replacement R0723100

Rebuild your booster pump's foundation with the genuine Polaris Pump Body (R0723100), a factory-spec replacement housing made exclusively for the Polaris PB4SQ. This OEM component restores the structural backbone of your pump, ensuring proper internal alignment and consistent water pressure output. Manufactured from tough, chemically resistant materials that withstand high-pressure pool operation, the R0723100 lets you repair housing damage without the expense of a complete...

Polaris PB4SQ Energy Efficient Multistage Booster Pump | TEFC Motor | 0.97 HP 115/230V

The Polaris PB4SQ™ Multistage Booster Pump harnesses a .97 HP TEFC motor running on 115/230V to deliver outstanding energy savings without sacrificing cleaning power. Featuring a multistage impeller design, this pump runs at remarkably low noise levels while providing the precise water pressure that Polaris pressure-side cleaners demand. Streamlined installation and simplified serviceability make the PB4SQ™ an ideal upgrade for pool owners seeking peak performance...

Polaris PB4SQ Pump O-Ring Set & Drain Plug R0734300

Eliminate leaks and restore airtight pump operation with the genuine Polaris O-Ring Set and Drain Plug (R0734300). This comprehensive replacement kit is tailored for the Polaris PB4SQ booster pump and contains all the critical sealing components plus a new drain plug needed to maintain proper pressure and peak circulation. Every piece is manufactured from chemical-resistant materials that hold up against chlorine, heat, and continuous use,...

Polaris Plastic Wheel Washer for Vac-Sweep 180 & 280 Pool Cleaners – C64

The genuine Polaris C64 Plastic Wheel Washer is a factory-specification replacement component built for Polaris Vac-Sweep 180 and 280 pressure-side pool cleaners. Installed between the wheel and bearing assembly, this washer acts as a protective barrier that keeps contaminants away from the bearings while also guarding against damage caused by overtightened wheel lock screws. A complete wheel assembly calls for four of these washers to...

Polaris Pool Cleaner Back Up Valve Replacement | G52 | Swimables SW-62-052

Restore full navigational capability to your Polaris pressure-side pool cleaner with the Swimables SW-62-052 Back-Up Valve. Serving as a reliable replacement for models 180, 280, and 380, this valve plays a vital role in keeping your cleaner from becoming trapped in corners or along walls. Operating on a built-in timer, it activates roughly every 3 minutes and stays open for approximately 30 seconds, generating a...

Polaris Pool Cleaner Base Weight Replacement | Part 9-100-9004

Keep your Polaris pool cleaner tracking straight and covering every inch of your pool with the genuine Polaris Base Weight 9-100-9004. Specifically manufactured for the Polaris Vac-Sweep 380 and TR35P, this OEM ballast component anchors the cleaner at the proper operating angle so it glides smoothly across floors and walls without tipping or losing contact. Crafted from robust, chemically inert materials, it holds up to...

Polaris Pool Cleaner Bearing Shield Replacement | Part 9-100-7011

The genuine Polaris Bearing Shield 9-100-7011 is a precision-crafted OEM replacement component manufactured for Polaris Vac-Sweep 360, 380, TR35P, TR36P, and ATV pool cleaners. This bearing shield serves a critical function by safeguarding internal bearings—sealing lubricant inside and blocking contaminants from entering—so the cleaner's moving parts run without friction. Made from durable, high-grade materials, it boosts performance and prolongs the cleaner's operational lifespan. Fast and...

Polaris Pool Cleaner Feed Hose Float Replacement | D10

The genuine Polaris D10 feed hose float is an OEM replacement designed to keep the feed hose properly suspended in Polaris 180, 280, 380, and P39 pressure-side pool cleaners. Without adequate buoyancy, the hose can sink and drag along the pool floor, causing tangles that obstruct cleaner movement and reduce water flow. Constructed from resilient, chemical-resistant materials, this float maintains its buoyancy season after season...

Polaris Pool Cleaner Feed Pipe O-Ring Replacement | Part 9-100-5132

The genuine Polaris Feed Pipe O-Ring 9-100-5132 is an essential sealing component for Polaris 360, 380, TR35P, and TR36P pool cleaners. This O-ring forms a snug, drip-free connection at feed pipe junctions, helping preserve uniform water pressure and system efficiency. Made from durable materials, it withstands aggressive pool chemicals and fluctuating pressures, delivering dependable long-term service. Routinely swapping out worn O-rings is key to protecting...

Polaris Pool Cleaner Sweep Hose Barb Fitting | Part 9-100-7008

The genuine Polaris Sweep Hose Barb 9-100-7008 is an OEM replacement component designed to sustain the proper operation of Polaris Vac-Sweep 360 and 380 pool cleaners. This part firmly attaches the sweep hose to the cleaner body, maintaining consistent high-pressure water flow for effective debris displacement. It features an integrated adjustment screw, giving you the ability to fine-tune water pressure and avoid over-spraying. Built from...

Polaris Pool Cleaner Sweep Hose Scrubber 5-Pack | Black | CMP 9-100-3105 | 25563-300-500

Give your Polaris pressure-side cleaner renewed scrubbing power with the CMP Sweep Hose Scrubber 25563-300-500. This 5-pack replacement tail scrubber fits directly onto the sweep hose tip on Polaris Vac-Sweep 180, 280, 360, 380, 480 PRO, TR35P, TR36P, P39, and 3900 Sport cleaners. Each scrubber agitates and dislodges stubborn dirt, algae, and debris from pool walls, corners, and steps while simultaneously shielding the hose end...

Polaris PosiTrax Tire C13 | Fits 360 & 380 Pool Cleaners

Get superior surface grip where it matters most with the genuine Polaris PosiTrax Tire C13. Specifically created for Polaris 360 and 380 pressure-side pool cleaners, this replacement tire excels on smooth, hard-to-grip surfaces like fiberglass and tile. Its specialized tread compound grabs hold of slick areas, helping your cleaner ascend walls and navigate tricky spots without hesitation. Constructed from long-wearing, high-traction rubber, the C13 maintains...

Polaris Quattro P40 Q4000 Factory Tune-Up Kit | R0995100

The OEM Polaris Quattro Factory Tune-Up Kit R0995100 provides every essential internal component needed to bring a Polaris Quattro pressure-side cleaner back to like-new condition. The kit bundles drive shaft and gearbox assemblies, brush gearboxes, axles, cyclonic turbines, and wheel bearings, each precision-manufactured to original factory tolerances. Replacing these high-wear parts in a single service session restores smooth mechanical operation and extends the overall lifespan...